Plumber's Essentials: Your Key to Bathtub Installation
Plumber's Essentials: Your Key to Bathtub Installation
Blog Article
In this article below you can locate a good deal of exceptional tips around How to Install a Bathtub.
Installing a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bath tub with a new one is also a moderately challenging job. If the old tub is easily easily accessible, the task can relocate speedily; if you need to open up a wall to remove the old bathtub and also place the brand-new tub, the task is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will certainly need an assistant to leave the old bathtub and also set in the new one. Make certain you have certified on your own for the task and also are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is better to think about using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your restroom if you have already bought a brand-new bathtub as well as don't need to transform the setup of your previous supply of water pipelines.
Your devices and product checklist must consist of the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather troublesome because of the restricted gain access to that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making certain that the washers are in location between the tap and the sink. Safeguard the faucet in place with the producer provided backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former kind must be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Making use of the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water system and examine all joints and new pipework for leaks and also tighten them if essential. Fill the bath tub and likewise examine the overflow outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling and also securing around the bath tub should wait until the bathtub has been used at least once as this will settle it into its last placement.
Planning for the Installment
To start with, the supporting structure provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be suited its last position.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always fill up the bathtub with water prior to securing, to enable the motion experienced when the bathtub remains in usage. The sealer can split rather very early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I discovered that piece of writing on Tools You Need to Install a New Bathtub while surfing around the internet. Please take the time to distribute this blog entry if you liked it. I take joy in reading our article about How to Install a Bathtub.
Get Estimate Report this page